View our full imprinted concrete sealer range | PICS UK - Suppliers to trade

Imprinted Concrete Sealers

View our full range of pattern imprinted concrete sealers

Our range of sealers for imprinted concrete

High Solid Sealer

A high resin content acrylic sealer used for new pattern imprinted concrete projects, and where a higher sheen is preferred on reseal projects. Available in 25 litre drums, and applied by roller, brush or viton sealed hand pump sprayer units at an average coverage of 2-3 square metres per litre.

Purpose

To impregnate a PICSPAVE slab and combine the benefits of curing, hardening, dust proofing and sealing.

Special properties

  • Hardens & seals concrete permanently
  • Special blend of polymers do not soften in hot temperatures nor become brittle in freezing conditions
  • High viscosity ensures full penetration into the dense surface matrix creating a true in-surface seal (ISS)
  • Non-re-emulsifiable, non-blooming when wet
  • 100% inter-coat adhesion
  • Curing Agent – allows slab moisture emigration prior to reaching full hardness
  • Non-yellowing
  • Anti-carbonising agent
  • Mechanical bond with surface matrix prevents delamination
  • Tough, Durable and Hard Wearing
  • Designed for use with PICSPAVE to bring out and enhance the full depth of colour of the CSH (Colour Surface hardener) and RA (Release Agent).
  • Slip Resistant
  • Petrol, Diesel, Oil & Grease resistant

Application instructions

The slab must be fully surface dry after washing off (Protimeter 4.5 and below) and all traces of RA (Release Agent) removed by pressure washing and RAW (Release Agent Wash).

Brush slab to remove any dirt or debris.

Control joints must be cut prior to HSS application. HSS must be spray applied using a pressure spray unit equipped with Viton™ seals and solvent resistant hose and body. Apply in two equal applications, keeping sprayer head moving to avoid pooling. The first aapplication must be brushed into the surface and allowed to dry past tacky prior to applying the second coat.

Avoid application in strong, direct sunlight – do not apply if rain is likely within 3 hours of application.

Approximate coverage

4 to 6m2 per litre per application – two applications required.

Low Solid Sealer

A low resin content acrylic sealer used for resealing existing sealed pattern imprinted concrete or where a low sheen is preferred. Available in 25 litre drums, and applied by roller, brush or viton sealed hand pump sprayer units at an average coverage of 2-3 square metres per litre.

Purpose

To impregnate a PICSPAVE slab and combine the benefits of curing, hardening, dust proofing and sealing.

Special properties

  • Hardens & seals concrete permanently
  • Special blend of polymers do not soften in hot temperatures nor become brittle in freezing conditions
  • High viscosity ensures full penetration into the dense surface matrix creating a true in-surface seal (ISS)
  • Non-re-emulsifiable, non-blooming when wet
  • 100% inter-coat adhesion
  • Curing Agent – allows slab moisture emigration prior to reaching full hardness
  • Non-yellowing
  • Anti-carbonising agent
  • Mechanical bond with surface matrix prevents delamination
  • Tough, Durable and Hard Wearing
  • Designed for use with PICSPAVE to bring out and enhance the full depth of colour of the CSH (Colour Surface hardener) and RA (Release Agent).
  • Slip Resistant
  • Petrol, Diesel, Oil & Grease resistant

Application instructions

The slab must be fully surface dry after washing off (Protimeter 4.5 and below) and all traces of RA (Release Agent) removed by pressure washing and RAW (Release Agent Wash).

Brush slab to remove any dirt or debris.

Control joints must be cut prior to LSS application. LSS must be spray applied using a pressure spray unit equipped with Viton™ seals and solvent resistant hose and body. Apply in two equal applications, keeping sprayer head moving to avoid pooling. The first aapplication must be brushed into the surface and allowed to dry past tacky prior to applying the second coat.

Avoid application in strong, direct sunlight – do not apply if rain is likely within 3 hours of application.

Approximate coverage

4 to 6m2 per litre per application – two applications required.

Xtraseal

A high gloss resin content acrylic sealer used for new pattern imprinted concrete projects where a high gloss finish is required. Available in 25 litre drums and applied by brush, roller or viton sealed hand pump sprayer units at an average coverage of 2-3 square metres per litre.

Special properties

  • Hardens & seals concrete permanently
  • Special blend of polymers do not soften in hot temperatures nor become brittle in freezing conditions
  • High viscosity ensures full penetration into the dense surface matrix creating a true in-surface seal (ISS)
  • Non-re-emulsifiable, non-blooming when wet
  • 100% inter-coat adhesion
  • Curing Agent – allows slab moisture emigration prior to reaching full hardness
  • Non-yellowing
  • Anti-carbonising agent
  • Mechanical bond with surface matrix prevents delamination
  • Tough, Durable and Hard Wearing
  • Designed for use with PICSPAVE to bring out and enhance the full depth of colour of the CSH (Colour Surface hardener) and RA (Release Agent).
  • Slip Resistant
  • Petrol, Diesel, Oil & Grease resistant

Application instructions

The slab must be fully surface dry after washing off (Protimeter 4.5 and below) and all traces of RA (Release Agent) removed by pressure washing and RAW (Release Agent Wash).

Brush slab to remove any dirt or debris.

Control joints must be cut prior to Xtraseal application. Xtraseal must be spray applied using a pressure spray unit equipped with Viton™ seals and solvent resistant hose and body. Apply in two equal applications, keeping sprayer head moving to avoid pooling. The first aapplication must be brushed into the surface and allowed to dry past tacky prior to applying the second coat.

Avoid application in strong, direct sunlight – do not apply if rain is likely within 3 hours of application.

Approximate coverage

4 to 6m2 per litre per application – two applications required.

Xylene

A solvent based cleaning and thinning agent for use with xylene based sealers and viton sealed sprayer equipment. Used as a cleaning liquid for spillages of sealer or to reactivate cured acrylic sealer before reapplying new sealer. Available in 5 litre or 25 litre drums.

Follow us

Address

Unit 2
Red Shute Hill Industrial Estate
Hermitage
Newbury
Berkshire
RG18 9QL 

 © Pattern Imprinted Concrete Supplies Limited, Unit 2, Red Shute Hill Ind. Estate, Hermitage, Newbury, Berkshire RG18 9QL | Company number 02623534

Terms & Conditions and Privacy Policy